Basic Info
Model NO.: 5000s, 7000F, 2426H, C
Usage: General Plastics, Engineering Plastics, Specialty Plastics
CAS No: 9002-88-4
Specification: AAA
HS Code: 39012000
Material: High Density Polyethylene/HDPE
Color: Transparent White
Trademark: EO
Origin: China Product Description
Virgin and recycled HDPE&LDPE&LLDPE for different grade
Specifications
1. Virgin & Recycled
2. Type: Film grade, Injection molding grade, Blowing molding grade, extrusion grade,
3. Pack: 25kg/bag
Virgin & Recycled HDPE / LDPE / LLDPE granules
We are direct factory of HDPE, LDPE, LLDPE, PP granule, different MFR or MFI are available for your different usage.
1, Film Grade HDPE,
Stretch film tape, blown film, carrier bags, film extrusion, blending partner,
Bags and density modifies, products for use in property modification
2, Fiber or Monofilament HDPE,
Monofilament, ropes, yarns
3, Injection Moulding Grade HDPE,
House wares, caps, thin walled, Transport and stacking crates, Bottle crates, Lightweight household,
Disposable articles large, Molding and complicated parts, closures/seals, packaging, Engineering parts,
Transport containers, PET bottle base cap, Injection moulding grade specially for cap
4, Below Moulding Grade HDPE,
Petro cans, containers, disinfectant bottles, sheet for thermoforming, drums, heating oil strorage tanks,
Fabric softeners, Extrusion large blow moldings, bottle extrusion
5, Pipe Extrusion Grade HDPE,
PE80, PE100, gas/water pipe, UV Stabilization and pigments during processing.
6, Extrusion Grade HDPE,
Wire&Cable
| HDPE cable material Property | Unit | Typical Value |
| Mass density | g/cm 3 | 0.941-0.959 |
| Melt flow Rate(190 centidegree /2.16kg) | g/10min | ≤1.0 |
| Tensile yield strength | MPa | ≥19.0 |
| Flexural modulus | Mpa | ≥965 |
| Elongation@ break | % | ≥400 |
| Impact Embrittlement temperature | centidegree | MAX -118 |
| Dielectric Constant | 100KHZ | 2.32 |
| 1MHZ | 2.31 | |
| Loss Tangent | 100KHZ | MAX 0.0001 |
| 1MHZ | MAX 0.0001 | |
| Volume resistivity | OHM-CM | MIN 1x10 15 |
| Application | Mainly used for the production of high toughness of the telephone,cable insulation material | |
LDPE:
| Physical Properties | Test Method | Nominal Value | Unit | |
| Density | ISO 1183 | 0.921 | g/cm 3 | |
| Melt Mass-Flow Rate (MFR) | ISO 1133 | 1.9 | g/10min | |
| Hardness | ||||
| Shore Hardness (shore D) | ISO 868 | 45 | ||
| Mechanical Properties | ||||
| Tensile Modulus | ISO 527-2 | 175 | MPa | |
| Tensile Strength | Yield, | ISO 527-2 | 9.0 | MPa |
| Break, | 13.0 | MPa | ||
| Tensile Strain(Break) | ISO 527-2 | 850 | % | |
| Modulus of Elasticity | Internal Method | 250 | MPa | |
| Thermal | ||||
| Vicat Softening Temperature | ISO 306/A50 | 89.0 | °C | |
| Melting Temperature (DSC) | DIN 53765 | 108 | °C | |
| Peak Crystallization Temperature (DSC) | DIN 53765 | 97.0 | °C | |
| Heat of Fusion | DIN 53765 | 110 | J/g | |
| Electrical | ||||
| Volume Resistivity | ASTM D257 | 8.5E+15 | ohm ?cm | |
| Dielectric Strength | ASTM D149 | 30.0 | kV/mm | |
| Dielectric Constant (60Hz) | ASTM D150 | 2.20 | % | |
| Dissipation Factor (60 Hz) | ASTM D150 | 0.00050 | ||
LLDPE
| Properties | Test conditon | Test method | Test data | Unit |
| Density | 0.91 | |||
| MFI | 2 | |||
| Drop impact strength | ASTM D-1709 | 90 | g | |
| Elongation ,vertical/horizontal | ASTM D-882 | 600/800 | % | |
| tensilestrength,thermal resistance | ASTM D-1004 | 105/95 | Kg/cm | |
| elongation | ASTM D-638 | 930 | % | |
| tensile strength | ASTM D-638 | 180 | ||
| tensile strength,vertical/horizontal | ASTM D-882 | 380/350 | ||
| Vicat softening point | ASTM D-1525 | 103 | °C | |
| melting point | ASTM D-2117 | 126 | °C | |
| Turbidity | ASTM D-1009 | 12 | % | |
| 45 glossness | ASTM D-2457 | 75 | % | |
